...
How to correctly install the measuring cuvette in the Smart Tester
Incorrect installation of the measuring cuvette can cause incorrect measurement or even prevent correct measurement with the Smart Tester. An incorrectly installed measuring cuvette can cause:
measurement error issues,
calibration of the measuring cuvette issues,
taking a water sample into the measuring cuvette issues,
water leakage from the measuring cuvette issues,
adding chemical reagents issues.
The measuring cuvette should be placed in the measuring capsule, and the measuring capsule should be properly installed in the measuring chamber in the Smart Tester. There should be a magnetic stir bae in the measuring cuvette.
...
The correct and incorrect way to install the measuring cuvette is shown below.
...
dobrze
...
źle
...
Make sure that the measuring cuvette is properly seated in the measuring.
Note, the size of the measuring cuvette may vary slightly depending on the series. Therefore, a white stand (shown in the photo) may be added to some measuring cuvettes to properly seat them in the measuring capsule.
...
...
measuring cuvette is crookedly seated in the measuring capsule
...
Make sure that the measuring cuvette is properly seated in the measuring.
Note, the size of the measuring cuvette may vary slightly depending on the series. Therefore, a white stand (shown in the photo) may be added to some measuring cuvettes to properly seat them in the measuring capsule.
...
...
measuring cuvette is crookedly seated in the measuring capsule
...
Make sure that the measuring capsule is properly seated in the measuring chamber of the Smart Tester.
...
...
the measuring capsule with the measuring cuvette has not been inserted all the way into the measuring chamber
...
Make sure that the measuring capsule is properly seated in the measuring chamber of the Smart Tester.
...
...
the measuring capsule with the measuring cuvette has not been inserted all the way into the measuring chamber
...
Jak poprawnie zainstalować kuwetę pomiarową w Smart Testerze
Błędne ułożenie kuwety pomiarowej może być przyczyną nieprawidłowego pomiaru lub nawet uniemożliwić poprawny pomiar Smart Testerem. Błędnie zainstalowana kuweta pomiarowa może powodować:
błąd pomiaru,
problem z poprawną kalibracją kuwety pomiarowej,
problem z pobraniem próbki wody do kuwety pomiarowej,
wyciek wody z kuwety pomiarowej,
problem z dodaniem reagentów chemicznych.
Kuwetę pomiarową należy umieścić w kapsule pomiarowej, a kapsułę pomiarową należy prawidłowo zainstalować w komorze pomiarowej urządzenia Smart Tester. W kuwecie pomiarowej powinno znajdować się mieszadło magnetyczne.
...
Poniżej przedstawiono poprawny i błędny sposób montażu kuwety pomiarowej.
...
dobrze
...
źle
Upewnij się, że kuweta pomiarowa jest poprawnie osadzona w kapsule pomiarowej.
Uwaga, rozmiar kuwety pomiarowej może się nieznacznie różnić w zależności od serii. Dlatego do niektórych kuwet pomiarowych może zostać dodana biała podstawka (widoczna na zdjęciu), aby poprawnie ją osadzić w kapsule pomiarowej.
...
...
kuweta pomiarowa jest krzywo osadzona w kapsule pomiarowej
...
Upewnij się, że kuweta pomiarowa jest poprawnie osadzona w kapsule pomiarowej.
Uwaga, rozmiar kuwety pomiarowej może się nieznacznie różnić w zależności od serii. Dlatego do niektórych kuwet pomiarowych może zostać dodana biała podstawka (widoczna na zdjęciu), aby poprawnie ją osadzić w kapsule pomiarowej.
...
...
kuweta pomiarowa jest krzywo osadzona w kapsule pomiarowej
...
Upewnij się, że kapsuła pomiarowa jest poprawnie osadzona w komorze pomiarowej Smart Testera.
...
...
kapsuła pomiarowa z kuwetą pomiarową nie została włożona do końca w komorze pomiarowej
...
Upewnij się, że kapsuła pomiarowa jest poprawnie osadzona w komorze pomiarowej Smart Testera.
...
...
kapsuła pomiarowa z kuwetą pomiarową nie została włożona do końca w komorze pomiarowej